Align the threaded stems at the holes in the sink. Press the faucet firmly into place on the sink. Alternatively, for a three-piece set, install the faucets and spout at the appropriate holes in the sink. Reach under the sink and install one of the provided flat washers onto each threaded stem. Screw one of the provided nuts onto each stem. Hand-tighten the nuts against the underside of the sink. Align the center-set faucet fixture uniformly with the back edge of the sink bowl. Alternatively, for a three-piece set, ensure the spout points straight outward.
Tighten the nuts under the sink securely, using adjustable pliers. Once the faucet is in the mounting holes, insert a washer over each tailpipe, and then twist on the nuts by hand. To tighten the nuts, turn them to the right clockwise. Attach the water supply hoses. Start by attaching the hoses to the faucet first. Attach each hose to the tailpipe of the faucet, and then tighten the nut by hand. To finish tightening the nuts, use the basin wrench to turn each nut a quarter turn to the right clockwise.
Once the hoses are attached to the new faucet, reattach them to the water supply. Turn the nuts by hand to the right clockwise , then tighten them the rest of the way with the adjustable wrench. Turn on the water and test the faucet. When everything is connected and tightened, turn the water back on by turning the shutoff valve to the left counterclockwise.
Then turn on the taps to flush out the new faucet. When the water is running, check for leaks and drips. To flush the faucet, simply let the hot and cold water run for 1 to 2 minutes.
Layla Moulding. Not Helpful 0 Helpful 5. Include your email address to get a message when this question is answered. If the faucet bolts are stripped or rusted, you can score through the silicone that holds the vanity top in place. Remove the vanity top to allow easier access to remove the faucet. After disconnecting the supply lines and installing the new faucet, apply clear silicone caulking around the edges and set the vanity top back in place.
Then, reinstall the supply lines. Helpful 1 Not Helpful 0. Submit a Tip All tip submissions are carefully reviewed before being published. You Might Also Like How to. How to. More References 4. About This Article. Co-authored by:. Co-authors: 7. Updated: May 12, Categories: Faucets and Taps. Article Summary X Before replacing a bathroom faucet, turn off the water supply using the valve behind the sink, and drain the pipes beneath the basin.
Deutsch: Einen Wasserhahn im Bad austauschen. Thanks to all authors for creating a page that has been read 78, times. Reader Success Stories Elijah Jul 16, Did this article help you? Cookies make wikiHow better. By continuing to use our site, you agree to our cookie policy. Elijah Jul 16, Featured Articles How to.
Trending Articles How to. New Pages How to. To do this, unscrew the pivot nut on the body of the drain and insert the rod through the hole in the drain stopper. Replace the nut. Push down the horizontal rod assembly and secure the lift rod to the strap. Use the provided lift screw. Reconnect the feed lines in reverse order from the way you disconnected them earlier. Lift the hoses to the corresponding intake valves under each intake port.
Screw the fasteners into place with your hands, then use the wrench to tighten them down. Slowly twist the shutoff valve back open, listening for any leaks as water flows back into the system. Once water is flowing back into the faucet, test your connection and flush out the new fixture. Remove the aerator from the faucet mouth to allow minerals and other debris to exit the spout. Run the water until it seems to be totally clear. Try running hot and cold water to make sure both lines are properly feeding the sink.
See what plans are available in your neighborhood. HomeServe uses cookies to recognize repeat visits and to enhance your experience on our site.
By continuing to use this website you agree with our use of cookies. Privacy Policy. Please check back soon. HomeServe Logo Icon. The email field is required. Sign up! Check icon. Tools and Materials Needed The first step in any home improvement project is gathering tools and materials.
Remove the Faucet Start by disconnecting the supply lines from the underside of the faucet. Remove the Drain Many faucets come with matching drains.
0コメント